Just After Putting Bedding Compound In My Rifle :(

[GEOFF.223 83]

Just bedded my howa 1500 .223 with devcon steel putty.

 

Lets hope it comes away from stock ok tomorrow night

[charlie caller 3,654]

Yes lets hope you put lots of release compound on then pal

[GEOFF.223 83]

Yes lets hope you put lots of release compound on then pal

Release agent ?????

[walshie 2,804]

 

Yes lets hope you put lots of release compound on then pal

Release agent ?????

 

 

DOH!

[sussex 5,803]

Bedded for good ...!!!

[GEOFF.223 83]

Only messing plastered it in clear shoe polish.

 

Only bit im worried about it the stock bolts i covered them in polish but the compound came out top and bottom of the bolt cleaned away as much as possible. Its takes 24hrs to harden so going to try pull from stock at 5 ish

[GEOFF.223 83]

Just checked bolts there and there not stuck in so happy day's so far

[Deker 3,491]

As a matter of interest WHY are you bedding?

 

Were you getting problems or is this just an exercise?

 

Edit

Which stock is it?

Edited May 28, 2013 by Deker

[GEOFF.223 83]

As a matter of interest WHY are you bedding?

 

Were you getting problems or is this just an exercise?

 

Edit

Which stock is it?

It was a hogue\houge stock it was sitting to the left in the barrel chanel opened channel a little and bedded just for reinsurance.

 

Just finishd it and im very happy with results going to check zero and grouping tomorrow

[Deker 3,491]

 

As a matter of interest WHY are you bedding?

 

Were you getting problems or is this just an exercise?

 

Edit

Which stock is it?

It was a hogue\houge stock it was sitting to the left in the barrel chanel opened channel a little and bedded just for reinsurance.

 

Just finishd it and im very happy with results going to check zero and grouping tomorrow

 

 

Flippen 'ek, I would have thought it almost impossible to bed those Hogue jobs, they are incredibly flexible, Industrial size tub of Devcon required no doubt!

 

Any pics?

 

Good luck, hope it has done the job!

[GEOFF.223 83]

 

 

 

As a matter of interest WHY are you bedding?

 

Were you getting problems or is this just an exercise?

 

Edit

Which stock is it?

It was a hogue\houge stock it was sitting to the left in the barrel chanel opened channel a little and bedded just for reinsurance.

 

Just finishd it and im very happy with results going to check zero and grouping tomorrow

Flippen 'ek, I would have thought it almost impossible to bed those Hogue jobs, they are incredibly flexible, Industrial size tub of Devcon required no doubt!

 

Any pics?

 

Good luck, hope it has done the job!

Yeah got deacon free from work only bedded around rear pillar and recoil lug area dremeled ALOT of plastic away used half a tub of devcon might go tomorrow and buy 100 topshot fmj which were giving me 3 shoots at 1"at 100yards

[Deker 3,491]

 

 

 

As a matter of interest WHY are you bedding?

 

Were you getting problems or is this just an exercise?

 

Edit

Which stock is it?

It was a hogue\houge stock it was sitting to the left in the barrel chanel opened channel a little and bedded just for reinsurance.

 

Just finishd it and im very happy with results going to check zero and grouping tomorrow

Flippen 'ek, I would have thought it almost impossible to bed those Hogue jobs, they are incredibly flexible, Industrial size tub of Devcon required no doubt!

 

Any pics?

 

Good luck, hope it has done the job!

Yeah got deacon free from work only bedded around rear pillar and recoil lug area dremeled ALOT of plastic away used half a tub of devcon might go tomorrow and buy 100 topshot fmj which were giving me 3 shoots at 1"at 100yards