Jump to content
Sign in to follow this  
bigmac 97kt

Just An Other Old Chinese Model

Recommended Posts

Looking good for a B2. My mate had a B2 -2 I think it was called given the other week (Italian stock version the box called it) for a bit of messing we stripped it in my garage with a few tinnys as he was interested to see inside and....

 

A rear spring guide was fitted!

A fairly decent piston seal

Zero lube!

Lots of rust in cyl!

Lots of rust in barrel!

 

We cleaned it our with wd40 and rags on sticks, cleaned it out with de greaser then put some sandpaper on a rod and polished the cyl then the piston in the drill chuck till they where looking good and shiney!

 

When then lubed with my faveroute.... TBT bumslide and fitted a spare top hat from my draw (a hw one fitted) rebuilt - trigger was fiddly but we where a bit tiddly lol it was hard to guide the pin through. The result... Nice to shoot but this we need more barrel shims! That barrel is still loose. Was a fun evening tho and transformed it'd shot cycle. It sounded like a tool chest going down a flight of steps when fired before our little fettle .

  • Like 1

Share this post


Link to post

Si dont tell the bairn what iv got for him mate

 

if you have not all ready lol :laugh:

 

atvbjimmy :thumbs: :thumbs: :thumbs:

haha... I'm keeping schtum jimmy!

hes sat next to me tucking into ice-cream, can't wait to see him in his jungle warfare kit with his new springer :laugh::thumbs:

 

cheers si :thumbs:

  • Like 2

Share this post


Link to post

 

Si dont tell the bairn what iv got for him mate

 

if you have not all ready lol :laugh:

 

atvbjimmy :thumbs: :thumbs: :thumbs:

haha... I'm keeping schtum jimmy!

hes sat next to me tucking into ice-cream, can't wait to see him in his jungle warfare kit with his new springer :laugh::thumbs:

 

cheers si :thumbs:

 

Just polished the piston

 

and the new spring (well old one i had and reshaped it to fit in the piston lol)

 

Stephen (mad4it) is sending up a full rifle that is in bits so some of the parts i need will come out of that

 

just got to clean and polish the chamber

 

and just put two coats of tru oil on the stock she is looking good

 

and iv got the old piston and seal sitting in oil to swell it up a bit and give it a new lease of life

 

cant wait to see his face when he see,s it lol

 

atvbjimmy :thumbs: :thumbs: :thumbs:

post-63400-0-27906600-1492023828.jpg

post-63400-0-53944000-1492023838.jpg

post-63400-0-51710700-1492023848_thumb.jpg

post-63400-0-84654200-1492023856_thumb.jpg

  • Like 1

Share this post


Link to post

Looking good for a B2. My mate had a B2 -2 I think it was called given the other week (Italian stock version the box called it) for a bit of messing we stripped it in my garage with a few tinnys as he was interested to see inside and....

 

A rear spring guide was fitted!

A fairly decent piston seal

Zero lube!

Lots of rust in cyl!

Lots of rust in barrel!

 

We cleaned it our with wd40 and rags on sticks, cleaned it out with de greaser then put some sandpaper on a rod and polished the cyl then the piston in the drill chuck till they where looking good and shiney!

 

When then lubed with my faveroute.... TBT bumslide and fitted a spare top hat from my draw (a hw one fitted) rebuilt - trigger was fiddly but we where a bit tiddly lol it was hard to guide the pin through. The result... Nice to shoot but this we need more barrel shims! That barrel is still loose. Was a fun evening tho and transformed it'd shot cycle. It sounded like a tool chest going down a flight of steps when fired before our little fettle .

The trigger is fiddly as you have to put the trigger in then the spring for the trigger then the housing for the main spring then get the pin through all of them at the same time as well as pushing down on the housing for the main spring lol

 

The last one i did Tom nearly had me beat lol :laugh:

 

walked away from it three times until my son came in and it took 2 mins to sort after that with two of us lol :laugh:

 

atvbjimmy :laugh: :laugh: :laugh:

  • Like 1

Share this post


Link to post

 

 

Looking good for a B2. My mate had a B2 -2 I think it was called given the other week (Italian stock version the box called it) for a bit of messing we stripped it in my garage with a few tinnys as he was interested to see inside and....

 

A rear spring guide was fitted!

A fairly decent piston seal

Zero lube!

Lots of rust in cyl!

Lots of rust in barrel!

 

We cleaned it our with wd40 and rags on sticks, cleaned it out with de greaser then put some sandpaper on a rod and polished the cyl then the piston in the drill chuck till they where looking good and shiney!

 

When then lubed with my faveroute.... TBT bumslide and fitted a spare top hat from my draw (a hw one fitted) rebuilt - trigger was fiddly but we where a bit tiddly lol it was hard to guide the pin through. The result... Nice to shoot but this we need more barrel shims! That barrel is still loose. Was a fun evening tho and transformed it'd shot cycle. It sounded like a tool chest going down a flight of steps when fired before our little fettle .

The trigger is fiddly as you have to put the trigger in then the spring for the trigger then the housing for the main spring then get the pin through all of them at the same time as well as pushing down on the housing for the main spring lol

 

The last one i did Tom nearly had me beat lol :laugh:

 

walked away from it three times until my son came in and it took 2 mins to sort after that with two of us lol :laugh:

 

atvbjimmy :laugh: :laugh: :laugh:

Ha ha! Ace! It took two of us swearing at each other for half an hour to do that job. Its looking like your doing a top job there!

  • Like 1

Share this post


Link to post

 

 

Looking good for a B2. My mate had a B2 -2 I think it was called given the other week (Italian stock version the box called it) for a bit of messing we stripped it in my garage with a few tinnys as he was interested to see inside and....

 

A rear spring guide was fitted!

A fairly decent piston seal

Zero lube!

Lots of rust in cyl!

Lots of rust in barrel!

 

We cleaned it our with wd40 and rags on sticks, cleaned it out with de greaser then put some sandpaper on a rod and polished the cyl then the piston in the drill chuck till they where looking good and shiney!

 

When then lubed with my faveroute.... TBT bumslide and fitted a spare top hat from my draw (a hw one fitted) rebuilt - trigger was fiddly but we where a bit tiddly lol it was hard to guide the pin through. The result... Nice to shoot but this we need more barrel shims! That barrel is still loose. Was a fun evening tho and transformed it'd shot cycle. It sounded like a tool chest going down a flight of steps when fired before our little fettle .

The trigger is fiddly as you have to put the trigger in then the spring for the trigger then the housing for the main spring then get the pin through all of them at the same time as well as pushing down on the housing for the main spring lol

 

The last one i did Tom nearly had me beat lol :laugh:

 

walked away from it three times until my son came in and it took 2 mins to sort after that with two of us lol :laugh:

 

atvbjimmy :laugh: :laugh: :laugh:

Ha ha! Ace! It took two of us swearing at each other for half an hour to do that job. Its looking like your doing a top job there!

 

I was swearing at my self with sweat dripping off my brow lol

 

must of gone through 6 cigs in the time it took to get it in to calm my self down :laugh:

 

atvbjimmy :thumbs: :thumbs: :thumbs:

Share this post


Link to post

stripped the action back again Si as i was not happy with it

 

but it fine now phew

 

just waiting for some parts coming off mad4it (Stephen) then she will be ready for him

 

atvbjimmy :thumbs: :thumbs: :thumbs:

post-63400-0-99058200-1492331760.jpg

post-63400-0-38468800-1492331773.jpg

post-63400-0-39280000-1492331786.jpg

post-63400-0-87190200-1492331799.jpg

post-63400-0-47815000-1492331811.jpg

post-63400-0-66273600-1492331825.jpg

post-63400-0-04212400-1492331838.jpg

post-63400-0-23970200-1492331853.jpg

  • Like 2

Share this post


Link to post

Top job as usual!

Still a good few deep scratches in the stock Tom that i could not get out mate who ever had this before must of stripped the lacquer off with a wire brush some are that deep .

 

but as this is going to be used in the woods on woody's and crows it will not matter if it gets knocked and banged off the trees lol :laugh:

 

atvbjimmy :thumbs: :thumbs: :thumbs:

Share this post


Link to post

 

Top job as usual!

Still a good few deep scratches in the stock Tom that i could not get out mate who ever had this before must of stripped the lacquer off with a wire brush some are that deep .

 

but as this is going to be used in the woods on woody's and crows it will not matter if it gets knocked and banged off the trees lol :laugh:

 

atvbjimmy :thumbs: :thumbs: :thumbs:

 

it certainly will be used jimmy :thumbs:

can't wait for the summer... think its gong to be a good one!

cheers and ill see you and nelly friday :hunter::cheers:

atb si

Share this post


Link to post

 

 

Top job as usual!

Still a good few deep scratches in the stock Tom that i could not get out mate who ever had this before must of stripped the lacquer off with a wire brush some are that deep .

 

but as this is going to be used in the woods on woody's and crows it will not matter if it gets knocked and banged off the trees lol :laugh:

 

atvbjimmy :thumbs: :thumbs: :thumbs:

 

it certainly will be used jimmy :thumbs:

can't wait for the summer... think its gong to be a good one!

cheers and ill see you and nelly friday :hunter::cheers:

atb si

 

Looking forward to it bro

 

:boogy: :boogy: :boogy:

 

:thumbs: :thumbs: :thumbs:

  • Like 1

Share this post


Link to post

Well si its all done mate

 

he will get it tomorrow when i we come down bud

 

just need to sort a stock screw out for it to day

 

atvbjimmy :thumbs: :thumbs: :thumbs:

post-63400-0-57219500-1492679595.jpg

post-63400-0-59654900-1492679603.jpg

post-63400-0-13956400-1492679612.jpg

post-63400-0-57493100-1492679620.jpg

post-63400-0-63262600-1492679633.jpg

post-63400-0-81202800-1492679642.jpg

  • Like 2

Share this post


Link to post

Just cleaned the barrel out Si first pellet residue then rust took a good few pull throughs to get her clean feck knows what they have put up this barrel lol

 

atvbjimmy :thumbs: :thumbs: :thumbs:

post-63400-0-85469100-1492683162.jpg

Share this post


Link to post

Looking good Jimmy :)

Got a fridge full of beer for nelly n Viz and a jar of decaf and an e-cig for you!!

See you tomorrow :)

Atb and cheers si

  • Like 1

Share this post


Link to post

Looking good Jimmy :)

Got a fridge full of beer for nelly n Viz and a jar of decaf and an e-cig for you!!

See you tomorrow :)

Atb and cheers si

Feck the decaf and you know where to shove the Ecig

 

TWAT

 

see you tomorrow mate

 

atvbjimmy :thumbs: :thumbs: :thumbs:

  • Like 1

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  
  • Recently Browsing   0 members

    No registered users viewing this page.

×