Wanted Datstate

[tommy smith 5]

im looking for instruction book for daystate mk3 and dvd if any one can help me dont mind paying for it plz

[adolf 3]

hi buddy go onto daystate site and there is links on there for the manuals etc ,,,,,,,,,and instructions ,,,i will try and find a link now ok ,,,,,,,

[adolf 3]

STEP RESETTING THE MAGAZINE COUNTER, STAGE 1

1 Pull the trigger, then switch the safety switch to FIRE, a red
light will be on
2 The gun will beep and the red light will blink,
3 Release the trigger, the magazine counter is reset and the
gun is now ready for firing


STEP RESETTING THE SHOT COUNTER, STAGE 2

1 Pull the trigger, then switch the safety switch to FIRE, a red
light will be on
2 The gun will beep and the red light will blink
3 Keep trigger pulled for 3 seconds until a double beep and
blink is given after 3s
4 Release the trigger, the shot counter is now reset and the
gun is ready for firing


STEP TURNING ON AND OFF THE SAFETY LIGHT, STAGE 3

1 Pull the trigger, then switch the safety switch to FIRE, a red
light will be on
2 Keep trigger pulled until 3 beeps and blinks are given after
6s and release the trigger
3 Pull the trigger to toggle between normally off/on, 1 beep
and blink for off, 2 beeps and blinks for on.
4 Set the safety switch to safe, the safety light status is
programmed


STEP PROGRAMMING THE SHOT COUNTER, STAGE 4

1 Pull the trigger, then switch the safety switch to FIRE, a red
light will be on
2 The gun will beep and the red light will blink
3 Keep trigger pulled until 4 beeps / blinks are given after 9s
4 Release trigger and the gun is now in programming mode
with the shot count reset to zero
5 Each time the trigger is pulled a beep and blink will indicate
that the shot counter is increased by 10
6 When the required shot count is reached, set the safety
switch to safe, the shot count is now programmed


STEP TURNING OFF THE SHOT COUNTER, STAGE 4

1 Pull the trigger, then switch the safety switch to FIRE, a red
light will be on
2 The gun will beep and the red light will blink
3 Keep trigger pulled until 4 beeps / blinks are given after 9s
4 Release trigger and the gun is now in programming mode
with the shot count reset to zero
5 Do not pull the trigger again to leave the shot count at zero
6 Set the safety switch to safe, the shot counter is off


STEP TURNING ON AND OFF THE MAG COUNTER, STAGE 5

1 Pull trigger, then switch safety to FIRE, a red light will be on
2 Keep trigger pulled until 5 beeps / blinks are given after 12s
and release the trigger
3 Pull the trigger to toggle between off/on, 1 beep and blink for
off, 2 beeps and blinks for on
4 Set the safety switch to safe, the magazine counter status is
programmed


STEP PROGRAMMING POWER SETTING, STAGE 6

1 Pull the trigger, then switch the safety switch to FIRE, a red
light will be on
2 Keep trigger pulled until 6 beeps / blinks are given after 15s
3 Release trigger and the gun is now in programming mode
with power set to maximum
4 Each time the trigger is pulled a beep and blink will indicate
that the power has been reduced by one step
5 Set the safety switch to safe, the power level is programmed


STEP RESETTING THE GUN TO DEFAULTS

1 Pull the trigger, then plug in the charger plug with the safety
switch in the safe position, a yellow light is on
2 Keep trigger pulled for three seconds until 7 beeps are given
3
Release trigger and the gun is in charging mode and
returned to default settings: magazine counter off, magazine
count set to zero, shot counter off, safety light normally on,
shot count

[adolf 3]

http://www.daystate.com/handbooks.htm

 

 

click the link above ok mate ,,,,,,,,,,,,,,,,,,,,

Edited March 27, 2013 by adolf