RAMCAM 4 Posted May 14, 2009 Report Share Posted May 14, 2009 What is the best way of fitting sling swivel studs to the hw100t without attaching it to the bipod? Quote Link to post
Sterry 0 Posted May 14, 2009 Report Share Posted May 14, 2009 Depends if you want to be able to remove the sling get the QD studs (one long one short) and the sling bit to it. if not any kind will do from bisley just be sure to get a long and short one. Quote Link to post
Guest buster321c Posted May 14, 2009 Report Share Posted May 14, 2009 How you gettin on in Penkridge Ramcam? Quote Link to post
RAMCAM 4 Posted May 14, 2009 Author Report Share Posted May 14, 2009 How you gettin on in Penkridge Ramcam? Hi Buster I had a great time and met loads of friendly people. I shall be up there sunday, was hoping to get my rifle sling ready by then. T's wife told me over the phone today that a sling would cost me around £10 fitted only to find out that the studs were £30 for the pair, £15 for the swivels and a decent sling £25. I can not fit a sling to my bipod, I would have to change that aswell costing me another £50. What a day I would have to spend £120 just for a sling on my rifle. Quote Link to post
RAMCAM 4 Posted May 14, 2009 Author Report Share Posted May 14, 2009 Depends if you want to be able to remove the sling get the QD studs (one long one short) and the sling bit to it. if not any kind will do from bisley just be sure to get a long and short one. Do you know the cheapest place to purchase qd studs mate? would a stud be secure under the the hw100 the stocks a bit thin under the cylinder and the rifles a bit on the heavy side? Thanks Quote Link to post
Guest Scuba1 Posted May 14, 2009 Report Share Posted May 14, 2009 Drill the hole for the stud 0.5mm smaller then the stud, countersink it just a little bit ( before drilling put some masking tape on that area ) then mix some 2 component epoxy glue and put some on the stud before screwing it in. Leave to set for a few hours > Job done. It will hold no problem. HTH Michael Quote Link to post
RAMCAM 4 Posted May 15, 2009 Author Report Share Posted May 15, 2009 Drill the hole for the stud 0.5mm smaller then the stud, countersink it just a little bit ( before drilling put some masking tape on that area ) then mix some 2 component epoxy glue and put some on the stud before screwing it in. Leave to set for a few hours > Job done. It will hold no problem. HTH Michael Nice one thanks scuba. Quote Link to post
Guest Scuba1 Posted May 15, 2009 Report Share Posted May 15, 2009 Drill the hole for the stud 0.5mm smaller then the stud, countersink it just a little bit ( before drilling put some masking tape on that area ) then mix some 2 component epoxy glue and put some on the stud before screwing it in. Leave to set for a few hours > Job done. It will hold no problem. HTH Michael Nice one thanks scuba. Don't forget to set the stud holes at 90 degree to the stock of your gun ATB Michael Quote Link to post
RAMCAM 4 Posted May 15, 2009 Author Report Share Posted May 15, 2009 Drill the hole for the stud 0.5mm smaller then the stud, countersink it just a little bit ( before drilling put some masking tape on that area ) then mix some 2 component epoxy glue and put some on the stud before screwing it in. Leave to set for a few hours > Job done. It will hold no problem. HTH Michael Nice one thanks scuba. Don't forget to set the stud holes at 90 degree to the stock of your gun ATB Michael Yes that is a bit of a worry. Do you know where i can get some cheap studs from? i'm looking for the removable ones but can't find them cheaper than £30 for the pair. Quote Link to post
Guest Scuba1 Posted May 15, 2009 Report Share Posted May 15, 2009 No mate, I don't do fancy stuff like that. Just put two standard QD's in my rifles as I don't see the point in removing them. Sorry can't help you there. ATB Michael Quote Link to post
RAMCAM 4 Posted May 15, 2009 Author Report Share Posted May 15, 2009 No mate, I don't do fancy stuff like that. Just put two standard QD's in my rifles as I don't see the point in removing them. Sorry can't help you there. ATB Michael You've been very helpful thanks Scuba. Quote Link to post
Guest Scuba1 Posted May 15, 2009 Report Share Posted May 15, 2009 Thats what we are here for buddy. ATB Michael Quote Link to post
RAMCAM 4 Posted May 16, 2009 Author Report Share Posted May 16, 2009 How you gettin on in Penkridge Ramcam? Hi Buster Are you going to Penkridge mate? Quote Link to post
RAMCAM 4 Posted May 16, 2009 Author Report Share Posted May 16, 2009 Depends if you want to be able to remove the sling get the QD studs (one long one short) and the sling bit to it. if not any kind will do from bisley just be sure to get a long and short one. Managed to find the studs and quick release swivels on ebay £10 for the lot including postage from China. Thanks for your help Sterry Quote Link to post
Guest buster321c Posted May 16, 2009 Report Share Posted May 16, 2009 How you gettin on in Penkridge Ramcam? Hi Buster Are you going to Penkridge mate? Probably not mate , busy on permissions , i tend to go there when there no bunny`s about ,but at the minute there`s a few on the ground Quote Link to post
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.